Advanced Elements’ hybrid AirFusion EVO (AE1042) is a good looking PU-skinned IK that slipped under my radar for a year or two. It replaced AE’s AirFusion Elite (right) which used two low-pressure side bladders (four in total) stacked one over the other, and an alloy keel rod along a plain, single-skin PVC shell. Like a folding kayak there is no inflatable floor.
The EVO version (above) looks similar, but replaced the four bladders with a pair of PVC dropstitch panels running a much higher 6psi (0.41bar), but the shell is now much more supple PU. Both methods keep the boat slim, and bow and stern alloy ‘C’ ribs are tensioned by a long slot-in keel rod, like a thick tent pole.
On some older, low-psi AE’s these ‘backbones’ are optional, but on the AirFusion it’s part of the design. This rod gives the AirFusion a V-shaped hull (above) a bit like the inflatable AirBone keel on some FDS Kzone IKs, and also adds tension between the bow and stern which the dropstitch sides can’t do alone.
The AirFusion EVO is the opposite of most ‘hybrid (part dropstitch) IKs which combine DS floors with round tube sides. Such boats, like the Gumotex Rush, or Aquaglide Chelan are rigid but, with round side tubes, end up wider and so, more stable.
The new EVO retains the low-pressure thwarts (air bags, below left) which help push the deck rod up so water runs off, push the sides and the floor rod out to make the skin taught, and up front, give something for your feet to push against (assuming the span is correct for you; there’s some adjustment in the seat). There are additional small airbags at the bow and stern to firm up the wave-cutting plastic mouldings there. As you can see, they’re as sharp as a hardshell sea kayak. The coaming (deck rim) is inflatable too, as is the seat base. And the EVO’s seat’s backrest has been made taller for better support.
The AE1042 is all wrapped in a PU shell – yes, you read that right; it’s not cheaper, stiffer and possibly heavier PVC. That makes it a sort of ‘shell & bladder’ IK with the drying issues that entails; made a little harder by the fixed deck. As with the bow and stern ribs, the DS panels are fixed with velcro but are pre-positioned out of the box. They can be easily removed (or even just part-deflated inside and separated from the shell) for a deep dry and clean.
Numbers are a very light 14.5kg/32lbs; 4m long x 61cm wide (13′ x 24″). Because of the lack of an inflatable floor, the capacity is a modest 106kg (235lbs) and, as the air bag thwarts take up interior space, like the all-DS AirVolution, this ends more of a day boat than an overnight camping tourer. But that is what most people want in an IK.
At 24 inches wide this is also one of the narrowest IKs around, similar to Itiwit’s 25-inch X500. That means it should also be fast, but the X500 is known to be tippy (it’s worse for larger paddlers). You’d think the AirFusion might be the same, but without an inflatable floor you sit a few inches lower (as in a hardshell kayak) which greatly aids stability. Certainly online reviews don’t mention the AirFusion’s tippiness as much as the X500 which runs 10psi. (Dropping the pressure a bit can improve things at the cost of outright performance.)
The integrated rear plastic moulding can take a skeg which is optional (or ‘free’ from some outlets). This is not your usual slot-in sharks-fin under the boat, but a rudder-like pivoting blade (below left) which can be lifted and dropped as needed on a loop cord.
I tried a similar MYO rudder set up but ended up a lot of unavoidable but annoying ancillary rigging. But I’ve often thought of adding something like this skeg to my own IKs to eliminate scraping in shallow water, or especially when beaching a loaded boat which needs to be rested on a rock your mate’s boat (above right) if the under-skeg is not be be stressed. I looked briefly on eBay but couldn’t see a similar but cheaper pivoting skeg direct from China. They must be out there of cough up 80 sovs for the AE one.
You may get by without the skeg on the AirFusion as the V-floor also includes shallow strakes (inch-high keel strips) which will aid tracking while not getting in the way when on land or in shallows. A couple of reviewers have mentioned this PU shell is easily holed when scraping. Maybe they went a bit too far to get the weight low, but a quick bit of tape easily fixes that as the skin is separate from the pressured D-S panels. The 2021 EVO has had an added panel of PU welded along the keel line where most wear occurs
Assembly does seem quite a faff compared to simply inflating three chambers (read the manual here or watch the vid below), but as with all things, you’ll get the hang of it. Remember, you’ll have the same alloy-framed folding kayak worries with salt and grit getting into the anodised alloy tube joints after sandy or saltwater paddles. The assembly video below shot on a sandy beach made me wince a bit.
But as with a folding kayak, it may all be worth it if performance is responsive once on the water. Some photos do show a saggy, creased shell (left) – you’d think they could have made a better fit, or more likely this boat could do with a few more psi.
And the sides are quite tall and slabby (also typical of a FDS IK) which will make it susceptible to side winds, especially without a skeg. That’s the case with most IKs, but you’d think with a single skin floor and a deck, it could be nice and low, like a Feathercraft.
With all the rods it looks as bulky as PVC DS or bladder IKs, but at under 15kg it certainly is light for a 4-m boat and appears to zip along. The back deck has an integrated velcro hatch / rolltop drybag and you have your usual bungy deck lines to stash a paddle while having a breather.
In the US the AirVolution EVO goes for $1200; that works out as £1200 in the UK, plus a $/£40 pump which will need three nozzles for the raft, Boston and twist lock valves. That’s still nearly twice the price of the X500 or a FDS IK like the Shipwreck, but there are no other boats quite like this.
Here an owner’s review.